Ford uses a constant control relay module that controls fuel pumps, fans, and other things. They generally have 4 or 5, 40 amp relays and a water tight sealed connector. Picking these up with the connector from the junk yard is pretty cheap and replaceable.
Check this out it will show what they ...
Search found 8 matches
- Sun Mar 06, 2016 7:45 pm
- Forum: MS-II Ignition Setup, Tuning, and Troubleshooting
- Topic: Waterproof relay board alternative
- Replies: 6
- Views: 927
- Sat Sep 20, 2014 7:17 am
- Forum: Wiring and Sensors
- Topic: Found a reasonbly priced E85 sensor PN13577394
- Replies: 0
- Views: 1541
Found a reasonbly priced E85 sensor PN13577394
Well went looking for parts on Ebay, fishing expedition basically and just typed in flex fuel sensor and up pops a pass thru sensor rather than a u-shaped in/out .
I figured this would be better for less restriction. as its a straight through design and has quick connects.
This is stock for a 2011 ...
I figured this would be better for less restriction. as its a straight through design and has quick connects.
This is stock for a 2011 ...
- Tue Sep 09, 2014 6:18 pm
- Forum: Injectors, Fuel & Air Supply
- Topic: Suddenly Running Lean
- Replies: 10
- Views: 830
Re: Suddenly Running Lean
Because when a cylinder or two or more fail too fire it drives the AFR LEAN due to having NOT used the air for combustion. O2 sensors rear O2 after reaching over 600F DEG when they go active. NOT fuel. See an engine management system is used to READ the air used by the engine, if an engine gets ...
- Tue Sep 09, 2014 5:53 pm
- Forum: Wiring and Sensors
- Topic: Alternatives to the DIY relay board?
- Replies: 13
- Views: 1368
Re: Alternatives to the DIY relay board?
For some relay setups that are controlled check out like a 98 Escort, under the battery is a box called a CCRM or Constant Control Relay Module it has like 4 or 5 relays inside and they are like 40 or 50 amp relays. Snag one from JY with the plug, bolts in easy and it has two fan relays, fp relay ...
- Tue Sep 09, 2014 5:09 pm
- Forum: Wiring and Sensors
- Topic: small VR sensor
- Replies: 6
- Views: 644
Re: small VR sensor
Try a GM wheel speed sensor from a Blazer. Napa PN SC497.
- Sun Oct 13, 2013 5:16 pm
- Forum: General Information
- Topic: turbo sbc addvice
- Replies: 3
- Views: 601
Re: turbo sbc addvice
As for remote throttle body, that is not required nor really a good set up if you have a Holley pattern intake. On Ebay you can source a very nice 1000 cfm throttle body for cheap, also DITAutoune has one too.
Big issue is matching the TPS output to the MS you use. For timing on SBS go over to ...
Big issue is matching the TPS output to the MS you use. For timing on SBS go over to ...
- Sun Oct 07, 2012 2:55 pm
- Forum: General Information
- Topic: OK need some refreshing and help from users,,
- Replies: 1
- Views: 249
OK need some refreshing and help from users,,
My boss is running a mini sprint with 600cc Honda FTZ built CBR engine and after having located an FI intake that we might be able too use.
So they run in an unlimited class basically, he is running Methanol right now, but may be able to talk him into gas to keep price down till we can get methanol ...
So they run in an unlimited class basically, he is running Methanol right now, but may be able to talk him into gas to keep price down till we can get methanol ...
- Sun Oct 07, 2012 2:42 pm
- Forum: General Information
- Topic: Edelbrock proflo 1
- Replies: 8
- Views: 511
Re: Edelbrock proflo 1
Edelbrock computer is built by Magneti Marelli. And since most sensors are probably GM or Ford MS should work with any of them. Dont remeber but I believe Pro Flo runs either GM or Chrysler 4.0 IAC.
MS-II V3.0 or MS-3 should be awesome.
MS-II V3.0 or MS-3 should be awesome.