need experienced tuner near tampa, florida

williamb82 · Post by **williamb82** » Tue Apr 14, 2009 1:42 pm

looking for someone to give me some pointers and maybe help me tune my car thats in or near tampa. ive got a good base tune but have some parts of the fuel map that need work. i get a loud backfire at 5600rpm and it doesnt want to rev past. even though revlimit is 7k etc...

if your local and have experience tuning lmk.

engine is a toyota 7mgte
780cc/min injectors
walbro 255lph pump
ct26 turbo upgraded to 57 trim compressor
4bar map
edis 6 ignition with stock 7mgte coils.
gm air and engine temp sensors
stock 7mgte tps
aem wideband

ms2 v3.0 board with flyback for low impedance injectors

later it will have a gt4082 turbo with front facing intake with 3in tb and ford tps, a aeromotice a1000 pump with new feed and return lines to the rail etc.. and a custom 8an fuel rail.

S.Bretz · Post by **S.Bretz** » Wed Apr 15, 2009 6:46 pm

Sounds like the ignition may not be set properly. You sure you have it set for eids?
Have you tried to confirm the ignition advance with a timing light to make sure it accurate?

What area of tampa are you in?
What's your schedule like these days?

williamb82 · Post by **williamb82** » Thu Apr 16, 2009 9:25 am

yes its set for edis6. it runs great below 5600rpm. pulls extreamly hard. i can break my nitto drag radials loose in 3rd from a roll before they are fully warmd up. 1st and 2nd break loose from a roll even once warm. i blew the hg so will be changing it in the next week or 2 so i can get more tuning done before the new engine is done being rebuilt.

im off wed, sat and sun currently and live near hillsborough ave and i275.

williamb82 · Post by **williamb82** » Fri Apr 24, 2009 9:09 am

so no reply fro mthe previous guy. anyone else?

S.Bretz · Post by **S.Bretz** » Sat Apr 25, 2009 12:52 pm

Have you tried using the edis coil?

williamb82 · Post by **williamb82** » Mon Apr 27, 2009 4:38 pm

no i havent. there have been others that used the edis 6 with the stock 7mgte coils with no issues at all. one guy has made over 700hp with this setup. im working on getting some 2jzgte individual coils and will hook up the 2nd edis 6 module in parallel so i can run all 6 properly. but that wont be for a lil while. i should be able to purchase a set of those coils this week.

S.Bretz · Post by **S.Bretz** » Fri May 01, 2009 8:52 am

Hmm... I was wondering if the dwell in the edis might not be compatible with the stock coils.

Does it break up when you are light on the throttle; when you aren't making any boost?

S.Bretz · Post by **S.Bretz** » Fri May 01, 2009 11:35 am

DO you ever go out to any of the local meets? Other then the Saturday night 'shens at GIS and CCC.

williamb82 · Post by **williamb82** » Thu Jun 25, 2009 5:18 am

i loaded the msq from feb when it ran the best though now that its so much hotter out i cant boost like i used to. now the bucking happens at much lower boost pressures and lower rpms. made a quick datalog with it bucking in 2nd gear. ive attached them

williamb82 · Post by **williamb82** » Fri Jun 26, 2009 5:14 pm

well its raining and im bord so tweaked the timing table after viewing all the timing tables i could find for turbo engines. heres what i got

also tweaked the afr table from what it was. between this and the ign table i think ill be ok. i can prolly add more timing in but will wait to do that till i can go on a dyno. ill load the file and test it tomarow when it isnt raining. lol.

MSefi.com read only forum (Jan.15,2018)

need experienced tuner near tampa, florida

need experienced tuner near tampa, florida

Re: need experienced tuner near tampa, florida

Re: need experienced tuner near tampa, florida

Re: need experienced tuner near tampa, florida

Re: need experienced tuner near tampa, florida

Re: need experienced tuner near tampa, florida

Re: need experienced tuner near tampa, florida

Re: need experienced tuner near tampa, florida

Re: need experienced tuner near tampa, florida

Re: need experienced tuner near tampa, florida