I have a Ford EDIS-6. The MS wiring diagram shows pins 10-12 wired to corresponding pins 1-3 of the coilpack, but the color code on my unit shows that 10 (ylw/blk) goes to coilpack pin 3 (ylw/blk), pin 11 (ylw/wht) to coilpack pin 2 (ylw/wht and pin 12 (ylw/red) goin to coilpack pin 3 (ylw/blk). is this intentional or an error?
Regards,
Al
EDIS coil wiring diagram pins swapped
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Re: EDIS coil wiring diagram pins swapped
If it's the same as the 8 cylinder one, it does show the connections to the coils swapped. But also swaps the plug connections - so you end up OK. This got me confused as the coils were marked as to which cylinders they go to, and I had the connectors for both controller and coils with pigtails so wanted to use the correct colour cable.71911 wrote:I have a Ford EDIS-6. The MS wiring diagram shows pins 10-12 wired to corresponding pins 1-3 of the coilpack, but the color code on my unit shows that 10 (ylw/blk) goes to coilpack pin 3 (ylw/blk), pin 11 (ylw/wht) to coilpack pin 2 (ylw/wht and pin 12 (ylw/red) goin to coilpack pin 3 (ylw/blk). is this intentional or an error?
Regards,
Al
So I did a new drawing:-
Dave P, London UK.
Rover V-8
MSII V3
EDIS
Tech Edge Wideband
Rover V-8
MSII V3
EDIS
Tech Edge Wideband
Re: EDIS coil wiring diagram pins swapped
EDIS 6 ia a bit tricky. By setting it up on my test bench and spinning the VR wheel slowly by hand watching the plug pair firing I determined :
EDIS module pin 10 = Spark A
EDIS module pin 11 = Spark C
EDIS module pin 12= Spark B
So on a MB straight six with 1-5-3-6-2-4 firing order the A coil (EDIS pin 10)fires 1/6, the B coil ( EDIS pin 12) fires 5/2 and the C coil ( EDISpin 11) fires 3/4
Best regards
Heribert
EDIS module pin 10 = Spark A
EDIS module pin 11 = Spark C
EDIS module pin 12= Spark B
So on a MB straight six with 1-5-3-6-2-4 firing order the A coil (EDIS pin 10)fires 1/6, the B coil ( EDIS pin 12) fires 5/2 and the C coil ( EDISpin 11) fires 3/4
Best regards
Heribert
If it is not understood , it will not work!