Thinking of putting the EDIS 4 module next to the MegaSquirt II box and have both under the dash. Wondering if anyone has run what will turn out to be a shielded 8' long lead from the sensor to the EDIS module? (my sensor is a AIRTEX / WELLS Part # 5S1739)
Did some searching but did not find what I wanted, would appreciate if anyone can point me in the right direction
Dennis
EDIS 4 module distance from sensor
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Re: EDIS 4 module distance from sensor
Sorry, the sensor part number is Wells SU248
-
kjones6039
- Master Squirter
- Posts: 618
- Joined: Sat Jul 22, 2006 7:02 pm
- Location: Eureka, Nevada USA
- Contact:
Re: EDIS 4 module distance from sensor
I don't know why that wouldn't work just fine. I got rid of my EDIS module, so I had to rewire the vr sensor all the way to MS which is located under the dash also. An easy 7 feet I would guess. I wouldn't doubt that feeding the EDIS with a wire that long would work just as well.
Ken
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
Re: EDIS 4 module distance from sensor
Can't see it being a problem with a decent screened cable. You may have to increase the wire gauge between the EDIS module and the coils, though, if this is much longer than normal.
Dave P, London UK.
Rover V-8
MSII V3
EDIS
Tech Edge Wideband
Rover V-8
MSII V3
EDIS
Tech Edge Wideband
Re: EDIS 4 module distance from sensor
Thanks everyone, this is what I was hoping for...... can make the wire gauge slightly larger, grounded on one end and it sounds like it should work.
Dennis
Dennis