error loading firmware
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
wisemanbuilds
- MegaSquirt Newbie
- Posts: 1
- Joined: Mon Oct 23, 2017 7:44 pm
error loading firmware
ms2 trying to load firmware it seems to load and then when verifying it runs into various errors is there anybody who has ran into this problem and worked through it. every thread I read that has similar problems just dead ends with no solutions... please help
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: error loading firmware
Please post a screen shot of the messages you got. There may be important clues in their exact wording.
Re: error loading firmware
One thing I discovered is it needs a decent power supply. Seems to need more current to load code than simply running with a Stim on test. Just something to check. Other thing is I always use the old desktop with proper serial port. Takes one more thing like the USB adaptor out of the equation.
Dave P, London UK.
Rover V-8
MSII V3
EDIS
Tech Edge Wideband
Rover V-8
MSII V3
EDIS
Tech Edge Wideband
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: error loading firmware
Very true. 9 volt batteries sometimes run out of power before they can load firmware.trakkies wrote: Thu Oct 26, 2017 5:13 am One thing I discovered is it needs a decent power supply. Seems to need more current to load code than simply running with a Stim on test. Just something to check. Other thing is I always use the old desktop with proper serial port. Takes one more thing like the USB adaptor out of the equation.
-
kjones6039
- Master Squirter
- Posts: 618
- Joined: Sat Jul 22, 2006 7:02 pm
- Location: Eureka, Nevada USA
- Contact:
Re: error loading firmware
Agreed. I have never had a problem with the stim though.
Ken
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7