Looking for a shop or individual in Michigan to tune my MS

DSMHybred · Post by **DSMHybred** » Mon Aug 14, 2006 4:31 pm

So heres the story I built my engine installed my engine built my MS installed my MS and now I dont have a clue how to tune it. I look at the megamanual and it might as well be in greek. I am just not getting it. I am just looking for someone that knows what they are doing to help me get this thing tuned in. I am sure I could figure it out with help or someone can just tune the damn thing. I will pay cold hard cash based on experiance. Heres the setup I am running.

Car:
1996 Mitubishi Eclipse with a 420a motor
Star stage 2 turbo kit
DSM turbo 440cc injectors
All the little extra bells and whistles that are needed to run turbo and MS

MS:
MS I V2.2

ilostmymindcom · Post by **ilostmymindcom** » Mon Aug 14, 2006 5:05 pm

Where in Michigan?

DSMHybred · Post by **DSMHybred** » Mon Aug 14, 2006 5:49 pm

I am located in Southern michigan 20 mins east of Coldwater 35 mins south west of Jackson. Very easy to get to and will give travel bonus or trailer car to your location.

DSMHybred · Post by **DSMHybred** » Tue Aug 15, 2006 10:09 am

Anyone?

TPI 85 Blazer · Post by **TPI 85 Blazer** » Thu Aug 17, 2006 5:33 pm

I'm up in Saginaw, but my MS vehicle isn't even running right now, so I might not be your best candidate.

ilostmymindcom · Post by **ilostmymindcom** » Sat Aug 19, 2006 8:18 pm

I'm by the Indiana state line, but as well as him, my MS car isnt running.. not due to me being lazy, or not being able to tune.. due to faulty hardware.

hal0n · Post by **hal0n** » Sun Aug 20, 2006 2:52 pm

I can take a look at it, if you want. I have a running ms'ed audi...and the guy that wrote megatune is my uncle (hi eric!).

Want to bring it out to dexter?

DSMHybred · Post by **DSMHybred** » Wed Aug 23, 2006 7:10 pm

Hey hal0n Dexter isnt to bad from me only like an hour. Please contact me at storm94@hotmail.com if your interested. Anyone else thats interested please email me there with some information about your experiance with MS.

kgwmu · Post by **kgwmu** » Sun Jun 15, 2008 1:23 pm

I know this is old but, bump to the top as I am looking for some help here in Michigan.

shameem · Post by **shameem** » Sun Jun 15, 2008 2:42 pm

I dont have MS on my car yet and i am slowly reading up on things - if you decide to do it yourself i can help interpret some of the stuff ( I am an engineer - so i guess i should be able to read "technical" documents....)

kgwmu · Post by **kgwmu** » Tue Jun 24, 2008 8:44 am

shameem wrote:I dont have MS on my car yet and i am slowly reading up on things - if you decide to do it yourself i can help interpret some of the stuff ( I am an engineer - so i guess i should be able to read "technical" documents....)

Thanks for the offer, I am also an engineer so I also "should"

be able to read these documents. I just can't understand how the software works and the readings that I see on my screen. I will have to read up some more and see what happens. shameem I will keep you in mind. If I have questions will give you a shout and see if you can help me.

FiatFreak · Post by **FiatFreak** » Tue Jun 24, 2008 5:03 pm

Hi there,

You really should do reasonably well following the steps in the Megamanual, seaching on topics you don't quite get, and just plugging away at it. Then, if you really get stuck, post specific questions along with your MSQ file and you'll most likely get the help you are looking for.

Patrick

MSefi.com read only forum (Jan.15,2018)

Looking for a shop or individual in Michigan to tune my MS

Looking for a shop or individual in Michigan to tune my MS

Re: Looking for a shop or individual in Michigan to tune my MS

Re: Looking for a shop or individual in Michigan to tune my MS

Re: Looking for a shop or individual in Michigan to tune my MS

Re: Looking for a shop or individual in Michigan to tune my MS