Ok guys, Im sorry if this seems like a noob question, but I dont know where to start getting my engine started.
Im running MSII code vs 2.891. I got my 85 1.6L SOHC escort motor to fire and run for about a minute on the VE table in the source code. It ran so rich that it died and after cranking shortly, the engine hydrolocked. I cleared the cylinders, and it cranks freely now. I generated a new VE table and now it seems as if It is not doing anything. I dont even get a stutter. I tried to fool around with cranking pulsewidth% but that seems to be in millisec now, and it doesnt seem like it should be. Everything on the web is in %.
Anyway, Im kind of lost, and I would be happy if I could get some direction. I am pretty new to tuning and I am happy and willing to learn all I can. Thank you in advance.
New to VE table generation
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
splatranger95
- MegaSquirt Newbie
- Posts: 9
- Joined: Wed Aug 31, 2011 2:09 pm
-
kjones6039
- Master Squirter
- Posts: 618
- Joined: Sat Jul 22, 2006 7:02 pm
- Location: Eureka, Nevada USA
- Contact:
Re: New to VE table generation
Are you sure you haven't fouled the plugs?It ran so rich that it died and after cranking shortly, the engine hydrolocked. I cleared the cylinders, and it cranks freely now.
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
-
splatranger95
- MegaSquirt Newbie
- Posts: 9
- Joined: Wed Aug 31, 2011 2:09 pm
Re: New to VE table generation
I cleaned them, but I should just replace them to be sure. They were pretty nasty. I feel like my VE table was close if not right, so I should have gotten it to at least idle so I could know what to change.
-
splatranger95
- MegaSquirt Newbie
- Posts: 9
- Joined: Wed Aug 31, 2011 2:09 pm
Re: New to VE table generation
Now I cant get the controller to connect to the computer..... THis is really pissing me off.