Ford Sierra 2.9 V6 Cologne Turbo

[Andymcf]

Hello,

Please excuse me if I am doing this wrong this is really my first post on any forum.

Basically I want to build a 2.9 v6 turbo sierra with a MS injection system but have no idea what I need or how to go about.

The main problem is that am almost certain that the engine I have requires Air Flow meters which am pretty sure will cause a problem. I believe that the 2.9's is a wasted spark engine as it has a distributor but not sure. I have began to gather information and from what I can tell you can buy a MSII board and then a E TFI board to all the standard ECU connect to plug straight in. but i want to do away with the Air flow meters to make it more fuel efficient, is that possible ( am fairly sure you can)?

What i have at the moment is a 2.9 engine which i am rebuilding and a 2.8 turbo engine which am hoping to take the turbo out of and attach to the 2.9 along with the MegaSquirt set up.

Would like to know peoples thoughts? Is it a good idea? Or would I be better to either put the 2.8 turbo in it or just put the 2.9 in it?

Any and all advice would be great!

Many thanks,
Andrew

[Matt Cramer]

Hello,

Please excuse me if I am doing this wrong this is really my first post on any forum.

Basically I want to build a 2.9 v6 turbo sierra with a MS injection system but have no idea what I need or how to go about.

The main problem is that am almost certain that the engine I have requires Air Flow meters which am pretty sure will cause a problem.

It's rare for an engine to actually require an air flow meter. The stock electronics might, but what the stock electronics need goes right out the window when you install MegaSquirt,

I believe that the 2.9's is a wasted spark engine as it has a distributor but not sure.

Wasted spark is a type of distributorless ignition - you'd either have wasted spark or a TFI distributor.

[Andymcf]

Hi Matt,

When you buy a MS2 board kit do you have to wire it specificity to my engine (stupid question I know) or can I buy one of the pre built ones on your website (http://www.DIYAutoTune.com/catalog/mega ... p-171.html)?

Ok well the engine i have is not wasted spark then its distributor, Fords TFi ignition system.

Is it possible to buy a complete pre wired MS2 Board and plug your EEC-IV board into and wire it up for my engine and plug it straight into the existing harness?

Many thanks,
Andrew.

[Matt Cramer]

Hi Matt,

When you buy a MS2 board kit do you have to wire it specificity to my engine (stupid question I know) or can I buy one of the pre built ones on your website (http://www.DIYAutoTune.com/catalog/mega ... p-171.html)?

TFI would need some mods, and it may also need to be modified for some additional I/O.

Is it possible to buy a complete pre wired MS2 Board and plug your EEC-IV board into and wire it up for my engine and plug it straight into the existing harness?

Many thanks,
Andrew.

We can build custom MS2s - contact us directly at websales@DIYAutoTune.com for details - but at present we don't offer the EEC-IV board assembled for European Fords. Sorry, but testing them out is a bit difficult. If someone was able to bring us a Sierra test car, they may be a good candidate for the MSPNP On Demand program.

[trakkies]

Hi Matt,

When you buy a MS2 board kit do you have to wire it specificity to my engine (stupid question I know) or can I buy one of the pre built ones on your website (http://www.DIYAutoTune.com/catalog/mega ... p-171.html)?

Ok well the engine i have is not wasted spark then its distributor, Fords TFi ignition system.

Is it possible to buy a complete pre wired MS2 Board and plug your EEC-IV board into and wire it up for my engine and plug it straight into the existing harness?

Many thanks,
Andrew.

Have you looked at the ExtraEFI site in the UK?