Automatic Mixture Control with Turbo at WOT
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
MikeLi
- MegaSquirt Newbie
- Posts: 1
- Joined: Tue Nov 23, 2004 8:05 pm
- Location: Brookly, New York
- Contact:
Automatic Mixture Control with Turbo at WOT
Question for all the knows about Automatic Mixture Control. My questions is does it work when I'm at WOT and a turbo motor? I know that at 100% TPS I don't get any EGO correction. So with out the EGO correction does Automatic Mixure Control work to adjust the VE tables?
Re: Automatic Mixture Control with Turbo at WOT
No it would be impossible - how would the processor know what to do if it doesn't know whether the mix is rich or lean ?
It is really not a good idea to use AMC at WOT because the response times of the ego sensors are too slow. You will not get consistent results.
It is really not a good idea to use AMC at WOT because the response times of the ego sensors are too slow. You will not get consistent results.
Re: Automatic Mixture Control with Turbo at WOT
You are better off useing the megalog viewer for WOT tuning. Just set your target A/F table a little extra rich in the disired boost sections and log a couple pulls. Then let MLV tune and adjust. After a couple repeats, it will be pretty close and you can go back and fine tune it.
MS2 v3.0 pcb, 2.891 firmware w/ flex fuel mod
Ford eDIS-4
1000cc injectors
Saturn 1.9L
....lots of boost with a 50 shot of anti-lag.
Ford eDIS-4
1000cc injectors
Saturn 1.9L
....lots of boost with a 50 shot of anti-lag.
Re: Automatic Mixture Control with Turbo at WOT
Mikeli,
You may also try looking at this thread: viewtopic.php?f=38&t=11981
The spreadsheet may be able to help you "predict" the EGO without having to wait for it to respond...
Go easy on it though.
You may also try looking at this thread: viewtopic.php?f=38&t=11981
The spreadsheet may be able to help you "predict" the EGO without having to wait for it to respond...
Go easy on it though.
FLY LOW - GO FAST - TURN LEFT!
http://www.p40warhawk.com/P-40sToday/P-40sToday.htm
http://www.p40warhawk.com/P-40sToday/P-40sToday.htm