Hi there, i boght megasquirt kit from www.DIYAutoTune.com, i pass all the steps, but i fnished here when i try to load the code and every time i get this massege
Reading C:/Program Files/MegaSquirt/Monitor_v2.890.abs.s19:
Detected MS-II (HCS12) code.
Entry point: 0x0000
Code range : 0x4000-0x3db420
File read successfully.
Opened comm port 1 at 115200.
ERROR: Unknown error status response, e=0x00
Elapsed time: 0.34 seconds
MegaSquirt Download 2.00
Reading C:/Program Files/MegaSquirt/Monitor_v2.890.abs.s19:
Detected MS-II (HCS12) code.
Entry point: 0x0000
Code range : 0x4000-0x3db420
File read successfully.
Opened comm port 1 at 115200.
ERROR: Unknown error status response, e=0x00
Elapsed time: 0.44 seconds
I ran the portchek and i get "s".
Can somebody tell my how to solve the problem.
and Sorry for my bad english.
Stuck loadind the code on MS2 V3
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Re: Stuck loadind the code on MS2 V3
I also don`t have the stimulator and i use the relay board to power megasguirt.
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: Stuck loadind the code on MS2 V3
The message "S" often means you have it set to the wrong COM port. Are you using a USB adapter?
Re: Stuck loadind the code on MS2 V3
No i`m using comm cable.
Portchek says this
com4 opened
9600baud
triyng ' s'
Portchek says this
com4 opened
9600baud
triyng ' s'
Re: Stuck loadind the code on MS2 V3
There`s somethink strange. When i power up the board with DC adaptor(13V ) it works i thought it too noisy, and then i powered it with the car batery(12.8V) it doesn`t start at all.
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: Stuck loadind the code on MS2 V3
So were you able to load the code with the DC adapter?
Re: Stuck loadind the code on MS2 V3
It`s all voltage problem but it`s so confusing. First with DC adaptor which i used when i run portchek it finds me that I have connected com, next when i power up with the car battery portchek sees nothing connected and i thought that the board don`t work but actualy it was working and i loaded the code succesfully.
Today maybe 4-5 hours i listed the half forum topics for this problem wiht this error and i didn`t find any asnwer to this problem. Olny in one old topic i find this
"had a simliar issue couldn't download firware with the ac adaptor on my stim, used a 12 volt DC source directly and it worked perfectly first time, chased my tail for a couple of hours first."
Maybe the DC adaptor is too noisy and the dougthboard is reseting all the time. So i decide to get the car battery in charge to power up the board and it loaded succesfuly
For thouse who get this error massage ERROR: Unknown error status response, e=0x00 the answer is to power up the board for loading the code with the car battery. For me it worked from the first time, when i used DC adaptor i tried 3 days to loaded with no success.
Today maybe 4-5 hours i listed the half forum topics for this problem wiht this error and i didn`t find any asnwer to this problem. Olny in one old topic i find this
"had a simliar issue couldn't download firware with the ac adaptor on my stim, used a 12 volt DC source directly and it worked perfectly first time, chased my tail for a couple of hours first."
Maybe the DC adaptor is too noisy and the dougthboard is reseting all the time. So i decide to get the car battery in charge to power up the board and it loaded succesfuly
For thouse who get this error massage ERROR: Unknown error status response, e=0x00 the answer is to power up the board for loading the code with the car battery. For me it worked from the first time, when i used DC adaptor i tried 3 days to loaded with no success.
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: Stuck loadind the code on MS2 V3
Any chance you might be grounding out VREF when it's on the car?
Re: Stuck loadind the code on MS2 V3
No chance at all. I`m still assembling my engine and everything in the car is a mess. So i take the battery at home next to my PC and wire everything.