Never sure where to post as there are so many forums for MS. Give it a go here.
I have been reading about the PWC but don't see it offered for sale anywhere.
http://www.megamanual.com/PWC/indexright.htm
Is it available, work in progress or a dead player?
Thanks
Precision Wideband controller
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
Bernard Fife
- Master Squirter
- Posts: 475
- Joined: Thu Oct 29, 2009 12:54 pm
Re: Precision Wideband controller
Fueler,
Apparently Bruce continues to work on this, and it isn't too far from release, if Bruce could find the time to work on it. He was going to do an update at the Portland meet (which was canceled because of travel issues and illnesses), so perhaps he will do an update here. You might try PM'ing him (he is user Bruce Bowling: memberlist.php?mode=viewprofile&u=6 )
Lance.
Apparently Bruce continues to work on this, and it isn't too far from release, if Bruce could find the time to work on it. He was going to do an update at the Portland meet (which was canceled because of travel issues and illnesses), so perhaps he will do an update here. You might try PM'ing him (he is user Bruce Bowling: memberlist.php?mode=viewprofile&u=6 )
Lance.
"Never wrestle with pigs. You both get dirty and the pig likes it.” - George Bernard Shaw
Re: Precision Wideband controller
Thanks, I was getting down to the point of needing to choose a dual WB controller and hoped this one might be ready for primetime.
Back to flipping coins on the others.
Back to flipping coins on the others.
-
Philip Lochner
- Helpful Squirter
- Posts: 96
- Joined: Thu Feb 16, 2006 5:18 am
- Location: South Africa
- Contact:
Re: Precision Wideband controller
I've been using Innovate LC-1 but I have also found that these DO NOT like to be powered up while cranking. I now install them so they only get power once the alternator starts charging using the D+ output to energize a relay which then feeds power to the LC-1. Innovate also has a new WBO called MTX-L of which I have no experience yet.
Best regards
Philip
'74 Jensen Interceptor Mk3 (MS-2 EFI, GPIO + GM 4L60e)
'80 Jaguar XJS 5.3L V12* (MS-2 EFI + dual EDIS-6)
and about 10 others.
Philip
'74 Jensen Interceptor Mk3 (MS-2 EFI, GPIO + GM 4L60e)
'80 Jaguar XJS 5.3L V12* (MS-2 EFI + dual EDIS-6)
and about 10 others.