Hi, i have TPS sensor from Fiat Uno 1.3 turbo and the sensor itself is not a potentiometer type. It`s just a switch in first position(when the throttle is closed) it grounds the signal. The second position is the signal wire goes to 5volts (vref) when throttle is half open until wide open throttle. I red that when the signal wire is grounded MS enter in Flood clear mode and when signal wire is linked with Vref wire MS enter in EGO feedback. So is it correct to use that TPS sensor or i have to look for a potentiometer type.
Sorry for my English !!!
About TPS sensor
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
john.p.clegg
Re: About TPS sensor
Toni
Someone may correct me but I think you will have to bin this sensor and find a potentiometer type...
John
Someone may correct me but I think you will have to bin this sensor and find a potentiometer type...
John
Re: About TPS sensor
Yep, ditch it. WHat is the part number? IS it a Bosch part?
MS2 Extra 2.0.1
4 x IRGB14C40LPbF driving wasted COP's BAE403
VR input (60-2 OEM wheel and sensor)
No relay board
4 cylinder n/a, 16v 1368cc Fiat Seicento
4 x IRGB14C40LPbF driving wasted COP's BAE403
VR input (60-2 OEM wheel and sensor)
No relay board
4 cylinder n/a, 16v 1368cc Fiat Seicento
Re: About TPS sensor
Yes it`s Bosch 0 280 120 314
Re: About TPS sensor
Is it the same as this:
If so, I do not know of a direct replacment.
I used a 0-280-122-001 but it is smaller, so you have to mount it on new holes. ALso, i had to cut the shaft down a bit to fit it on.
Kristian
If so, I do not know of a direct replacment.
I used a 0-280-122-001 but it is smaller, so you have to mount it on new holes. ALso, i had to cut the shaft down a bit to fit it on.
Kristian
You do not have the required permissions to view the files attached to this post.
MS2 Extra 2.0.1
4 x IRGB14C40LPbF driving wasted COP's BAE403
VR input (60-2 OEM wheel and sensor)
No relay board
4 cylinder n/a, 16v 1368cc Fiat Seicento
4 x IRGB14C40LPbF driving wasted COP's BAE403
VR input (60-2 OEM wheel and sensor)
No relay board
4 cylinder n/a, 16v 1368cc Fiat Seicento
Re: About TPS sensor
It`s almost the same and it`s not a problem to adjust it to fit.