Settings for dual o2 sensors.
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
ka24deroadster
- MegaSquirt Newbie
- Posts: 9
- Joined: Wed Jul 27, 2011 3:09 pm
Settings for dual o2 sensors.
I am running a MSii on my 1996 chevy LT1 (350 V8). I have 2 Innovate LC-1 wideband O2 sensors, one for the left and one for right side of the motor. I am using TunerStudio for tunning. What is the proper Tunner studio settings for dual 02 sensors. If I use a single VE table how does the Automatic Mixture Control(AMC) calculate the adjustments needed? Does it just average the two 02 readings? Is it better to run dual VE tables? If i run dual VE table, how do i match up the 02 sensors to the matching VE table? How do I pair up the 02 sensors with the matching bank of fuel injectors?
-
Bernard Fife
- Master Squirter
- Posts: 475
- Joined: Thu Oct 29, 2009 12:54 pm
Re: Settings for dual o2 sensors.
ka24r,
I had a quick look at the code, and I believe that dual EGO is used 'per bank' if dual tables are enabled. If dual tables are not enabled, it looks to me like EGOcorr2 is still applied to bank2 (and EGOcorr1 to bank1) - they just take the VE from the single table (but EGO2 has its own AFR table).
Bank1 is all the injectors connected to INJ1, which are any connected to DB37 pins 32 & 33.
Bank2 is all the injectors connected to INJ2, which are any connected to DB37 pins 34 & 35.
Lance.
I had a quick look at the code, and I believe that dual EGO is used 'per bank' if dual tables are enabled. If dual tables are not enabled, it looks to me like EGOcorr2 is still applied to bank2 (and EGOcorr1 to bank1) - they just take the VE from the single table (but EGO2 has its own AFR table).
Bank1 is all the injectors connected to INJ1, which are any connected to DB37 pins 32 & 33.
Bank2 is all the injectors connected to INJ2, which are any connected to DB37 pins 34 & 35.
Lance.
"Never wrestle with pigs. You both get dirty and the pig likes it.” - George Bernard Shaw