Hi, can anyone help me.. I have a proton satri Gti with a Mitsubishi galant 6A13 2.5 V6 twin turbo engine mounted in the rear, I'm currently building a single turbo conversion with tubular manifolds, relocated HX35 turbo, external waste gate and charge cooler also I will be replacing the injectors for some 580cc ones I have. I would like better control of my engine and I would like some sort of launch control or even an anti lag setup. The engine is currently controlled by a apexi safc and avcr with a wideband afm on the standard Mitsi ecu.
My questions are..
-Which ms system will I need? 1 2 or 3? I'm thinking 3?
-does ms have launch or anti lag features?
-is ms ok to use on a v6 turbo? (I'm guessing yes)
-can I run 6x coil on plug pencil type coils (I have Toyota ones on my Evo and want to use them on the proton)
-last question.. Where do I get a base map to load up and get running then start tuning?
Any help is appreciated.. I must admit I haven't done loads of research into the fitting and setup of the ecu but I thinking I can build the ecu and wire it to the engine but what's the next step when it needs programming? Obvs if it was say a ford zetec there's loads done but mine may be a bit more difficult? Especially when I try to and some mivec (variable cam) heads into the equation!!
Cheers Aaron.
Newbie question Mitsubishi 6A13TT
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: Newbie question Mitsubishi 6A13TT
That will depend on what features you need and what trigger wheel.A4RON wrote:My questions are..
-Which ms system will I need? 1 2 or 3? I'm thinking 3?
Note that MS3 and MS2/Extra have a separate support forum at MSExtra.com.
Bowling & Grippo code (covered here on this forum) - no.-does ms have launch or anti lag features?
MS2/Extra - launch only.
MS3 has full rally style antilag.
Yes, we've seen just about all types used on turbo / V6 applications.-is ms ok to use on a v6 turbo? (I'm guessing yes)
Not with Bowling & Grippo code.-can I run 6x coil on plug pencil type coils (I have Toyota ones on my Evo and want to use them on the proton)
MS2/Extra or MS3 can do this no problem.
The documentation walks you through setting up a startup map.-last question.. Where do I get a base map to load up and get running then start tuning?
